View 74LVQ37304_4984657.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

74LVQ373
LOW VOLTAGE CMOS OCTAL D-TYPE LATCH WITH 3 STATE OUTPUTS NON INVERTING
s
s s
s
s
s
s s
s
s
s
HIGH SPEED: tPD = 5.8 ns (TYP.) at VCC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: ICC = 4 A (MAX.) at TA=25C LOW NOISE: VOLP = 0.4V (TYP.) at VCC = 3.3V 75 TRANSMISSION LINE OUTPUT DRIVE CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0 V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 373 IMPROVED LATCH-UP IMMUNITY
SOP
TSSOP
Table 1: Order Codes
PACKAGE SOP TSSOP T&R 74LVQ373MTR 74LVQ373TTR
DESCRIPTION The 74LVQ373 is a low voltage CMOS OCTAL D-TYPE LATCH with 3 STATE OUTPUT NON INVERTING fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and low noise 3.3V applications. These 8 bit D-Type latch are controlled by a latch Figure 1: Pin Connection And IEC Logic Symbols
enable input (LE) and an output enable input (OE). While the LE inputs is held at a high level, the Q outputs will follow the data input precisely. When the LE is taken low, the Q outputs will be latched precisely at the logic level of D input data. While the (OE) input is low, the 8 outputs will be in a normal logic state (high or low logic level) and while high level the outputs will be in a high impedance state. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage.
July 2004
Rev. 5
1/13
74LVQ373
Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description
PIN N 1 2, 5, 6, 9, 12, 15, 16,19 3, 4, 7, 8, 13, 14, 17, 18 11 10 20 SYMBOL OE Q0 to Q7 D0 to D7 LE GND VCC NAME AND FUNCTION 3 State Output Enable Input (Active LOW) 3-State Latch Outputs Data Inputs Latch Enable Input Ground (0V) Positive Supply Voltage
Table 3: Truth Table
INPUTS OE H L L L LE X L H H D X X L H OUTPUT Q Z NO CHANGE* L H
X : Don't Care; Z : High Impedance * : Q outputs are latched at the time when the LE input is taken low logic level
Figure 3: Logic Diagram
2/13
74LVQ373
Table 4: Absolute Maximum Ratings
Symbol VCC VI VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 20 20 50 400 -65 to +150 300 Unit V V V mA mA mA mA C C
ICC or IGND DC VCC or Ground Current
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied
Table 5: Recommended Operating Conditions
Symbol VCC VI VO Top dt/dv Supply Voltage (note 1) Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 3.0V (note 2) Parameter Value 2 to 3.6 0 to VCC 0 to VCC -55 to 125 0 to 10 Unit V V V C ns/V
1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V
3/13
74LVQ373
Table 6: DC Specifications
Test Condition Symbol Parameter VCC (V) TA = 25C Min. 2.0 0.8 IO=-50 A 3.0 IO=-12 mA IO=-24 mA VOL Low Level Output Voltage IO=50 A 3.0 IO=12 mA IO=24 mA II IOZ Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) 3.6 3.6 3.6 3.6 VI = VCC or GND VI = VIH or VIL VO = VCC or GND VI = VCC or GND VOLD = 0.8 V max VOHD = 2 V min 0.1 0.25 4 36 -25 0.002 0 0.1 0.36 2.9 2.58 2.99 2.9 2.48 2.2 0.1 0.44 0.55 1 2.5 40 25 -25 Typ. Max. Value -40 to 85C Min. 2.0 0.8 2.9 2.48 2.2 0.1 0.44 0.55 1 5.0 40 A A A mA mA V V Max. -55 to 125C Min. 2.0 0.8 Max. V V Unit
VIH VIL VOH
High Level Input Voltage Low Level Input Voltage High Level Output Voltage
3.0 to 3.6
ICC IOLD IOHD
1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 75
Table 7: Dynamic Switching Characteristics
Test Condition Symbol Parameter VCC (V) 3.3 3.3 CL = 50 pF 3.3 0.8 V TA = 25C Min. Typ. 0.4 -0.8 2 -0.5 Max. 0.8 V V Value -40 to 85C Min. Max. -55 to 125C Min. Max. Unit
VOLP VOLV VIHD
VILD
Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3)
1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz.
4/13
74LVQ373
Table 8: AC Electrical Characteristics (CL = 50 pF, RL = 500 , Input tr = tf = 3ns)
Test Condition Symbol Parameter VCC (V) 2.7 3.3(*) 2.7 3.3(*) 2.7 3.3(*) 2.7 3.3 2.7
(*)
Value TA = 25C Min. Typ. 7.2 5.8 7.2 5.8 8.7 7.4 8.5 7.5 2.0 1.5 0.0 0.0 0.0 0.0 0.5 0.5 Max. 11.5 9.0 11.5 9.0 14.0 11.5 14.0 11.5 5.0 4.0 4.0 3.0 1.5 1.5 1.0 1.0 -40 to 85C Min. Max. 13.5 10.5 13.5 10.5 16.0 13.5 16.0 13.5 6.0 4.0 4.5 3.0 1.5 1.5 1.0 1.0 -55 to 125C Min. Max. 15.5 12.0 15.5 12.0 18.5 15.5 18.5 15.5 6.0 4.0 4.5 3.0 1.5 1.5 1.0 1.0 ns ns ns ns ns ns ns Unit
tPLH tPHL tPLH tPHL tPLZ tPHZ tPZL tPZH tW tsL tsH thL thH tOSLH tOSHL
Propagation Delay Time LE to Q Propagation Delay Time D to Q Output Disable Time Output Enable Time LE Pulse Width HIGH Setup Time D to LE, HIGH or LOW Hold Time D to LE, HIGH or LOW Output To Output Skew Time (note1, 2)
3.3(*) 2.7 3.3(*) 2.7 3.3 2.7 3.3
(*)
(*)
ns
1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tPHLn|) 2) Parameter guaranteed by design (*) Voltage range is 3.3V 0.3V
Table 9: Capacitive Characteristics
Test Condition Symbol Parameter VCC (V) 3.3 3.3 3.3 fIN = 10MHz TA = 25C Min. Typ. 4 8 10 Max. Value -40 to 85C Min. Max. -55 to 125C Min. Max. pF pF pF Unit
CIN COUT CPD
Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1)
1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per Latch)
5/13
74LVQ373
Figure 4: Test Circuit
TEST tPLH, tPHL tPZL, tPLZ tPZH, tPHZ
CL = 50pF or equivalent (includes jig and probe capacitance) RL = R1 = 500 or equivalent RT = ZOUT of pulse generator (typically 50)
SWITCH Open 2VCC Open
Figure 5: Waveform - LE To Qn Propagation Delays, LE Minimum Pulse Width, Dn To LE Setup And Hold Times (f=1MHz; 50% duty cycle)
6/13
74LVQ373
Figure 6: Waveform - Output Enable And Disable Times (f=1MHz; 50% duty cycle)
Figure 7: Waveform - Propagation Delay Time (f=1MHz; 50% duty cycle)
7/13
74LVQ373
SO-20 MECHANICAL DATA
DIM. A A1 B C D E e H h L k ddd 10.00 0.25 0.4 0 mm. MIN. 2.35 0.1 0.33 0.23 12.60 7.4 1.27 10.65 0.75 1.27 8 0.100 0.394 0.010 0.016 0 TYP MAX. 2.65 0.30 0.51 0.32 13.00 7.6 MIN. 0.093 0.004 0.013 0.009 0.496 0.291 0.050 0.419 0.030 0.050 8 0.004 inch TYP. MAX. 0.104 0.012 0.020 0.013 0.512 0.299
0016022D
8/13
74LVQ373
TSSOP20 MECHANICAL DATA
mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0 0.45 0.60 0.05 0.8 0.19 0.09 6.4 6.2 4.3 6.5 6.4 4.4 0.65 BSC 8 0.75 0 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 6.6 6.6 4.48 0.002 0.031 0.007 0.004 0.252 0.244 0.169 0.256 0.252 0.173 0.0256 BSC 8 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0079 0.260 0.260 0.176 inch
A
A2 A1 b e K c L E
D
E1
PIN 1 IDENTIFICATION
1
0087225C
9/13
74LVQ373
Tape & Reel SO-20 MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.8 13.2 3.1 3.9 11.9 12.8 20.2 60 30.4 11 13.4 3.3 4.1 12.1 0.425 0.520 0.122 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 1.197 0.433 0.528 0.130 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch
10/13
74LVQ373
Tape & Reel TSSOP20 MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.8 6.9 1.7 3.9 11.9 12.8 20.2 60 22.4 7 7.1 1.9 4.1 12.1 0.268 0.272 0.067 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.276 0.280 0.075 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch
11/13
74LVQ373
Table 10: Revision History
Date 29-Jul-2004 Revision 5 Description of Changes Ordering Codes Revision - pag. 1.
12/13
74LVQ373
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
13/13

▲Up To Search▲

Price & Availability of 74LVQ37304

	To Download 74LVQ37304 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .